Ice Maker Installation Guide
Tools Needed:
- Phillips screwdriver
- Flathead screwdriver
- Nut driver set
- Pliers
- Multimeter
- Safety gloves
Step-by-Step Installation
- Safety First: Unplug refrigerator from power outlet before beginning any installation work.
- Remove Old Ice Maker: Remove mounting screws and disconnect electrical connector and water line from existing ice maker.
- Prepare New Unit: Remove all packaging materials from new ice maker assembly.
- Connect Water Line: Attach water supply line to inlet valve using proper fittings. Ensure connections are tight but not over-tightened.
- Mount Ice Maker: Position ice maker in mounting location and secure with provided screws.
- Electrical Connection: Connect electrical harness to refrigerator main board.
- Test Operation: Restore power, initiate ice maker cycle, and check for proper water flow and ice production.
- Final Check: Verify no water leaks and that ice maker fills, freezes, and ejects ice properly.
Ice Maker Specifications
| Part Number | WPW10704657 |
| Compatible Series | Whirlpool WRF, WRX, WRS Models |
| Ice Maker Type | Automatic Ice Maker Assembly |
| Ice Production Rate | 4-6 lbs per day |
| Voltage Requirements | 120V AC, 60Hz |
| Water Pressure | 20-120 psi |
| Water Line Size | 1/4" OD copper or plastic tubing |
| Ice Cube Size | Standard (adjustable on some models) |
| Temperature Range | 0°F to 10°F (-18°C to -12°C) |
| Dimensions (HxWxD) | 8.5 x 6.25 x 9.75 inches |
| Weight | 2.8 lbs |
| Material | Food-grade plastic and stainless steel |
Warranty Information
- Parts Warranty: 1 year limited warranty
- Labor Coverage: 90 days from installation
- Extended Options: Available through Whirlpool protection plans
For warranty service, contact Whirlpool Customer Service at 1-800-253-1301 or visit Whirlpool.com
Key Components
Ice Maker Assembly
Complete ice maker unit including motor, gears, and housing. This is the main component that produces and ejects ice cubes into the storage bin.
Water Inlet Valve
Solenoid-controlled valve that regulates water flow into the ice maker. Features built-in filter screen to prevent sediment buildup.
Ice Maker Harness
Electrical wiring harness that connects the ice maker to the refrigerator's main control board for power and communication.
Ejector Blades
Stainless steel blades that rotate to push ice cubes out of the mold. These blades are durable and resistant to corrosion.
Thermostat
Temperature sensor that monitors ice mold temperature and signals when ice is frozen and ready for ejection.
Fill Tube
Water delivery tube that directs water from the inlet valve into the ice mold. Includes heating element to prevent freezing.
Ice Production Cycle Components
Fill Phase
Water inlet valve opens, filling ice mold with precise amount of water
Freeze Phase
Refrigerator freezer maintains 0°F temperature to freeze water into ice
Harvest Phase
Heater warms mold, ejector blades rotate to release ice cubes
Ejection Phase
Ice cubes are pushed into storage bin, cycle resets automatically
Shutoff Arm
Mechanical arm that stops ice production when bin is full
Control Module
Electronic board that manages timing and sequencing of all phases
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No ice production | Water supply issue, clogged filter, faulty inlet valve | Check water supply, replace filter, test inlet valve operation |
| Small or hollow ice cubes | Low water pressure, restricted water flow | Check water pressure, inspect fill tube for restrictions |
| Ice maker runs continuously | Faulty thermostat, stuck shutoff arm | Test thermostat, ensure shutoff arm moves freely |
| Ice cubes stuck in mold | Heater element failure, mold warping | Test heater continuity, inspect mold for damage |
| Water leaking from ice maker | Cracked fill tube, loose connections | Inspect fill tube, tighten all water connections |
| Ice maker not ejecting ice | Motor failure, gear damage, blade obstruction | Test motor operation, inspect gears and blades |
Error Codes & Diagnostics
- IF: Ice maker failure - Check power and connections
- WF: Water flow issue - Check supply line and inlet valve
- FF: Freezing failure - Check freezer temperature
- EF: Ejection failure - Inspect ejector mechanism
- HF: Heater failure - Test mold heater element
- SF: Sensor failure - Check thermostat and sensors
Parts Manual Downloads
Current Model Parts Manuals
WPW10704657
Standard Ice Maker Assembly
WPW10704658
Deluxe Ice Maker with Sensor
WPW10704659
Commercial Grade Ice Maker
WPW10704660
French Door Ice Maker Kit
Replacement Parts & Kits
WPW10704661
Water Inlet Valve Kit
WPW10704662
Ice Maker Motor Assembly
WPW10704663
Complete Repair Kit
WPW10704664
Thermostat & Sensor Kit