Installation Guide
Tools Needed:
- Multimeter
- Nut drivers (1/4" and 5/16")
- Screwdrivers (flat and Phillips)
- Pliers (needle nose and slip joint)
- Ice maker test harness
- Water pressure gauge
Step-by-Step Installation
- Prepare Work Area: Unplug refrigerator and turn off water supply. Clear area around ice maker for safe access.
- Remove Old Ice Maker: Remove mounting screws and disconnect electrical connector and water line from existing ice maker.
- Install New Ice Maker: Position new ice maker and secure with mounting screws. Ensure proper alignment with ice bucket.
- Connect Water Supply: Connect water line to inlet valve using proper fittings. Check for leaks with pressure test.
- Electrical Connection: Connect electrical harness to ice maker module. Ensure secure connection.
- Test Operation: Restore power and water supply. Initiate test cycle to verify proper ice production and harvesting.
- Final Check: Monitor first complete ice making cycle to ensure proper fill, freezing, and ejection.
Specifications
| Model Series | W10822278 / 8176235 |
| Type | Automatic Ice Maker Module |
| Compatible With | Whirlpool Refrigerator Models |
| Ice Production | 4-6 lbs per day |
| Ice Storage Capacity | 3-5 lbs |
| Ice Cube Size | Standard / Crushed Selectable |
| Voltage Requirements | 120V AC, 60Hz |
| Water Pressure | 20-120 psi |
| Water Consumption | 0.5 gallons per cycle |
| Cycle Time | 90-120 minutes |
| Dimensions (HxWxD) | 8.5 x 5.5 x 9.25 inches |
| Weight | 2.5 lbs |
Warranty Information
- Parts Warranty: 1 year limited warranty
- Labor Warranty: 90 days from installation
- Extended Coverage: Available through Whirlpool service plans
For warranty service, contact Whirlpool Customer Service at 1-800-253-1301 or visit Whirlpool.com
Key Features
Automatic Shutoff
Built-in sensor automatically stops ice production when bucket is full, preventing overflow and waste.
Quick Ice Production
Produces first batch of ice within approximately 90 minutes of initial installation or reset.
Dual Ice Options
Provides both standard ice cubes and crushed ice options for different beverage needs.
Self-Cleaning Cycle
Built-in cleaning cycle helps maintain hygiene and prevent mineral buildup from water supply.
Diagnostic Mode
Integrated diagnostic system helps identify common issues through error codes and test cycles.
Quiet Operation
Designed for minimal noise during ice production and harvesting cycles.
Ice Making Process Explained
Fill Cycle
Water valve opens to fill ice mold with precise amount of water
Freeze Cycle
Refrigerator cooling system freezes water in mold (approximately 20-30 minutes)
Harvest Cycle
Heater warms mold to release ice cubes into storage bucket
Ejection
Ejector blades rotate to push ice cubes into collection bin
Sensor Check
Level sensor checks if bucket is full before starting next cycle
Reset
System resets and prepares for next ice making cycle
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No ice production | Water supply issue, shutoff arm position, power problem | Check water supply, ensure shutoff arm is down, verify power to unit |
| Small or hollow ice cubes | Low water pressure, clogged water filter, faulty fill valve | Check water pressure (min 20 psi), replace water filter, test fill valve |
| Ice maker runs continuously | Faulty thermostat, stuck shutoff arm, control board issue | Test thermostat, check shutoff arm movement, inspect control board |
| Ice cubes stuck in mold | Heater failure, thermostat issue, mineral buildup | Test heater element, check thermostat, clean mineral deposits |
| Water leaking from ice maker | Overfilling, cracked water tube, faulty fill valve | Adjust fill time, inspect water tube, replace fill valve |
| Ice tastes or smells bad | Old ice, dirty water filter, contaminated water supply | Discard old ice, replace water filter, check water quality |
Error Codes & Diagnostics
- No Power: Check electrical connection and household circuit breaker
- No Water Flow: Verify water supply valve is open and filter is not clogged
- Continuous Run: Test thermostat and shutoff sensor with multimeter
- Heater Failure: Check heater element continuity (should be 50-100 ohms)
- Motor Failure: Test motor windings and gear mechanism
- Fill Valve Issue: Listen for click when activated, test solenoid coil
Manual Downloads
Current Ice Maker Models
W10822278
Standard Ice Maker Module
8176235
Ice Maker Assembly Kit
W10730942
Ice Maker with Quick Connect
WPW10730942
Professional Series Ice Maker
Popular Replacement Parts
WPW10304167
Ice Maker Fill Valve
W10807477
Ice Maker Thermostat
W10807478
Ice Maker Heater
W10807479
Ice Maker Motor Module