whirlpool model wrx988sibm01 manual

The Whirlpool Model WRX988SIBM01 is a 36-inch French Door Refrigerator with 28 cubic feet capacity, external ice and water dispenser, fingerprint-resistant stainless steel finish, adaptive defrost system, dual cooling system, LED lighting, adjustable gallon door bins, humidity-controlled crispers, and spill-proof glass shelves. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water Supply 7. Using Ice & Water Dispenser 8. Temperature Management 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: French door design with bottom freezer, external ice/water dispenser, digital controls, dual evaporators, adaptive defrost technology.

FeatureDescription
Capacity28 cubic feet total (19.7 cu ft fresh food, 8.3 cu ft freezer)
Ice & Water DispenserExternal dispenser with crushed/cubed ice and filtered water
FinishFingerprint-resistant stainless steel
Cooling SystemDual cooling with separate evaporators for fridge/freezer
Defrost SystemAdaptive defrost for energy efficiency
LightingLED interior lighting
ShelvingSpill-proof tempered glass shelves
Door StorageAdjustable gallon door bins
CrispersHumidity-controlled crispers for produce
ControlsDigital touch controls with temperature display

Installation

Unpack and inspect contents. Ensure proper clearance and leveling.

  1. Remove packaging: Remove all tape, foam, and protective film.
  2. Position refrigerator: Allow 2-inch clearance at back, 1-inch at sides, top clearance as needed.
  3. Level the unit: Adjust front leveling legs for stability.
  4. Connect water supply: Use 1/4-inch copper tubing or approved water line kit.
  5. Plug into dedicated 115V AC, 60Hz grounded outlet.

WARNING! Refrigerator is heavy; use two people for moving. Ensure floor can support weight.

First-Time Setup

Power on refrigerator; allow 24 hours for cooling stabilization.

  1. Set temperatures: Use digital controls to set fridge (37°F recommended) and freezer (0°F recommended).
  2. Enable ice maker: Lift wire signal arm to ON position.
  3. Flush water system: Dispense 2-3 gallons of water to clear lines.
  4. Install water filter: Insert filter and flush per instructions.
  5. Organize interior: Adjust shelves and bins as needed.

CAUTION! Do not load food until temperature indicators show proper cooling.

Specifications

Controls and Settings

Digital control panel located on dispenser front.

Display Features: Temperature readouts, filter status indicator, ice type selection, control lock, Sabbath mode.

Temperature Settings: Fridge (34°F to 46°F), Freezer (-6°F to 6°F). Ice Options: Cubed, crushed, off. Special Modes: Control lock (hold LOCK 3 seconds), Sabbath mode (hold LOCK and LIGHT 3 seconds), filter reset (hold FILTER 3 seconds after replacement).

Connecting Water Supply

Required for ice maker and water dispenser operation.

  1. Turn off main water supply.
  2. Connect 1/4-inch water line to cold water pipe with shut-off valve.
  3. Route line to refrigerator connection at bottom rear.
  4. Connect line to refrigerator inlet valve.
  5. Turn on water and check for leaks.
  6. Flush system before first use.

Tip: Use copper tubing or FDA-approved plastic water line. Do not use old plastic lines.

Using Ice & Water Dispenser

Dispenser located on exterior door.

  1. Select ice type: Press CUBED or CRUSHED button.
  2. Dispense ice: Press glass against paddle or press button.
  3. Dispense water: Press glass against paddle or press WATER button.
  4. Child lock: Press and hold LOCK 3 seconds to disable dispenser.
  5. Replace filter: When FILTER light illuminates, replace EveryDrop™ Filter EDR3RXD1.

WARNING! Do not use with containers that cannot withstand pressure. Keep children away from dispenser.

Temperature Management

Dual cooling system maintains separate fridge/freezer climates.

Recommended Settings: Fresh food compartment: 37°F. Freezer compartment: 0°F. Adjust as needed for climate or usage. Adaptive Defrost: System monitors usage and adjusts defrost cycles automatically. Temperature Alerts: Display shows "PF" if power failure occurred; "HI" if temperature too high.

Care & Cleaning

Unplug before cleaning interior. Use mild detergent and warm water.

  1. Exterior: Clean stainless steel with manufacturer-recommended cleaner.
  2. Interior: Remove shelves and bins; wash with mild detergent.
  3. Dispenser: Wipe with soft cloth; clean ice bin monthly.
  4. Condenser coils: Vacuum every 6-12 months (located at rear bottom).
  5. Door seals: Clean with warm water and baking soda solution.

CAUTION! Do not use abrasive cleaners, ammonia, or chlorine bleach on stainless steel.

Regulatory Information

UL Listed. Energy Star® certified. Meets NSF/ANSI 42 for water filtration. Manufactured by Whirlpool Corporation. Copyright © Whirlpool Corporation. For support, visit www.whirlpool.com or contact 1-800-253-1301. EveryDrop™ is a trademark of Whirlpool Corporation.

Troubleshooting

SymptomPossible CauseCorrective Action
No ice productionWater supply/ice makerEnsure water connected; check ice maker arm position; wait 24 hours.
Water not dispensingFilter/line issuesReplace filter; check water supply valve; flush system.
Temperature too warmSettings/airflowCheck temperature settings; ensure vents not blocked; clean condenser coils.
Excessive frost in freezerDoor seal/defrostCheck door seals; ensure door closes completely; run defrost cycle.
Dispenser not workingControl lock/powerCheck control lock status; ensure refrigerator is powered.
Unusual noisesInstallation/partsEnsure level; check for loose parts; normal defrost/ice maker sounds.

Reset: Unplug for 5 minutes, then reconnect to reset control board.

Service: 1-800-253-1301; www.whirlpool.com

Whirlpool Model WRX988SIBM01 Manual © - All Rights Reserved 2025