Whirlpool GZ25FSRXY2 Ice Maker Manual

The Whirlpool GZ25FSRXY2 is a built-in ice maker designed for reliable ice production, featuring a compact design, efficient ice production cycles, easy installation, and user-friendly controls. It includes a removable ice bin, water filter indicator, adjustable ice cube size, and cleaning cycle. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Water Line Connection 7. Ice Production Cycle 8. Cleaning and Maintenance 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Ice maker assembly, Removable ice storage bin, Water inlet valve, Water filter, Control panel, Power cord.

Feature	Description
Ice Production Rate	Up to 25 lbs of ice per day
Ice Bin Capacity	Holds approximately 5 lbs of ice
Adjustable Cube Size	Small, Medium, Large settings
Water Filter Indicator	Light alerts when filter needs replacement
Cleaning Cycle	Sanitize mode for internal cleaning
Removable Ice Bin	Easy access for ice removal and cleaning
Power Requirements	120V AC, 60Hz
Water Line Connection	1/4" copper or plastic tubing
Control Panel	Power, Ice Size, Clean Cycle buttons
Installation Type	Built-in undercounter design

Installation

Unpack and inspect contents. Ensure proper location with adequate ventilation.

Choose location: Select a well-ventilated area near water supply and drain.
Connect water supply: Shut off main water, connect 1/4" tubing to water inlet valve.
Connect drain line: Attach drain hose to drain outlet (if applicable).
Electrical connection: Plug into dedicated 120V outlet.
Level the unit: Adjust leveling feet for proper operation.

WARNING! Ensure water supply is turned off before connecting. Use two people for handling due to weight.

First-Time Setup

Power on ice maker; follow initial setup procedure.

Flush water system: Run water through filter and lines for 2 minutes before making ice.
Install water filter: Insert filter and run water to remove air bubbles.
Select ice size: Press ICE SIZE button to choose preferred cube size.
Start ice production: Press POWER button to begin first ice cycle.
Allow initial production: First batch may take 24 hours to produce.

CAUTION! Do not consume first batch of ice. Discard initial production.

Specifications

Model: GZ25FSRXY2
Daily Ice Production: Up to 25 lbs
Storage Capacity: 5 lbs
Ice Cube Types: Full cubes only
Water Connection: 1/4" compression fitting
Power Requirements: 120V AC, 60Hz, 2.5A
Dimensions (HxWxD): 34.5" x 15.5" x 24.5"
Weight: 85 lbs
Water Pressure: 20-120 psi required
Operating Temperature: 50°F to 100°F ambient

Controls and Settings

Control Panel: POWER button, ICE SIZE selector, CLEAN CYCLE button, FILTER RESET indicator.

Operation: Press POWER to turn on/off. ICE SIZE cycles through Small, Medium, Large. CLEAN initiates cleaning cycle. FILTER light indicates when to replace water filter.

Settings: Ice size adjustment affects production time and cube density. Clean cycle runs for 15 minutes to sanitize internal components. Filter reset after replacing water filter.

Water Line Connection

Proper water connection is essential for optimal performance.

Turn off main water supply.
Connect 1/4" copper or plastic tubing to water inlet valve.
Use compression fittings for secure connection.
Ensure water pressure is between 20-120 psi.
Install water filter before first use.

Tip: Use a water pressure gauge to verify proper pressure. Install a shut-off valve for easy maintenance.

Ice Production Cycle

Complete cycle takes approximately 90 minutes.

Water fill: Water enters ice mold for 7 seconds.
Freezing: Compressor runs for 20-30 minutes to freeze water.
Harvest: Heater warms mold to release ice cubes.
Ejection: Ice cubes fall into storage bin.
Bin full: Sensor stops production when bin is full.

Normal Operation: Cycle repeats automatically. Production stops when bin is full or POWER is pressed.

Cleaning and Maintenance

Regular maintenance ensures optimal performance and ice quality.

Monthly: Clean ice bin with mild detergent and warm water.
Every 6 months: Replace water filter (or when indicator light comes on).
Every 6 months: Run cleaning cycle with approved cleaner.
Annually: Clean condenser coils (if accessible).

Cleaning Cycle: Press and hold CLEAN button for 3 seconds. Add approved cleaner to water reservoir. Cycle runs for 15 minutes.

Care & Cleaning

Unplug before cleaning. Use only approved cleaners. Never use abrasive materials.

CAUTION! Do not use harsh chemicals, bleach, or ammonia-based cleaners. Rinse thoroughly after cleaning.

Regulatory Information

UL Listed. FCC Part 15 compliant. CSA certified. Manufactured to meet NSF/ANSI 12 standards. Copyright © Whirlpool Corporation. All rights reserved. For support, visit www.whirlpool.com or contact 1-800-253-1301.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No ice production	Power/water supply	Check power connection; verify water supply is on; check water filter.
Small or misshapen ice	Water pressure/low temp	Check water pressure; ensure ambient temperature above 50°F.
Ice tastes or smells bad	Old filter/contamination	Replace water filter; clean ice maker; flush water lines.
Ice maker runs constantly	Bin full sensor	Check sensor for obstruction; ensure bin is properly seated.
Water leakage	Loose connections	Tighten water line connections; check drain hose; inspect water inlet valve.
Loud noises	Ice jam/component issue	Check for ice jam in mechanism; ensure unit is level; contact service if persistent.

Reset: Unplug for 5 minutes to reset electronic controls.

Service: 1-800-253-1301; www.whirlpool.com