Whirlpool Automatic Ice Maker Manual

The Whirlpool Automatic Ice Maker is a built-in or freestanding appliance designed to produce and store ice automatically. It features a user-friendly control panel, various ice cube sizes, a storage bin with a capacity of approximately X lbs, a water filter indicator, a cleaning cycle, and energy-saving modes. This manual covers safety instructions, installation, operation, maintenance, and troubleshooting for optimal performance.

1. Features at a Glance 2. Installation & Setup 3. Specifications 4. Controls and Indicators 5. Operating Instructions 6. Ice Production & Selection 7. Cleaning & Maintenance 8. Water Filter Replacement 9. Energy Saving Tips 10. Safety Information 11. Troubleshooting

Features at a Glance

Key components: Ice maker assembly, storage bin, control panel, water inlet valve, filter housing, drain system.

Feature	Description
Automatic Ice Production	Continuously makes ice when activated and water is supplied
Ice Size Selector	Choose between small, medium, and large ice cubes
Storage Bin	Holds freshly made ice; includes a scoop
Control Panel	Buttons for power, ice size, and cleaning cycle
Water Filter Indicator	Light alerts when filter needs replacement
Cleaning Cycle	Sanitizes the ice-making system
Energy Saver Mode	Reduces power consumption during low use
Shut-Off Arm	Automatically stops ice production when bin is full
Air Filter	Removable filter to keep ice fresh
Drain Connection	For periodic flushing and cleaning

Installation & Setup

Unpack and inspect contents. Ensure location is level and near a water supply and drain.

Connect water supply: Attach 1/4-inch copper tubing to water inlet valve. Ensure water line is turned on.
Connect drain line: Attach drain hose to provided outlet or drain pan.
Plug into dedicated 120V AC electrical outlet.
Turn on power and press the POWER button on the control panel.
Run initial ice-making cycle: The first batch may take up to 24 hours.

WARNING! Ensure water connection is secure to prevent leaks. Follow local plumbing codes.

Specifications

Model: Whirlpool Automatic Ice Maker (specific model number).
Ice Production: Up to X lbs per 24 hours.
Storage Capacity: X lbs of ice.
Ice Cube Sizes: Small, Medium, Large.
Water Supply: 1/4-inch copper tubing, 20-120 psi water pressure.
Power Requirements: 120V AC, 60Hz, X amps.
Dimensions (HxWxD): XX" x XX" x XX".
Operating Temperature: 50°F to 100°F ambient.
Filter Type: Replaceable water filter (model: XYZ).

Controls and Indicators

Control Panel: POWER button, ICE SIZE selector, CLEAN button, FILTER RESET indicator.

Indicator Lights: Power (green), Ice Full (amber), Filter (red), Clean (flashing).

Operation: Press POWER to turn unit on/off. Select ice size (S/M/L) for desired cube. Press CLEAN to initiate cleaning cycle (unit will beep when complete). Reset filter indicator after replacing filter.

Operating Instructions

Daily use for ice production and retrieval.

Ensure power is on and water supply is connected.
Select desired ice size using ICE SIZE button.
Ice maker will automatically produce ice until bin is full (shut-off arm will rise).
To retrieve ice, open bin door and use provided scoop.
If ice production stops, check if bin is full or if there is a water supply issue.

Tip: For best ice quality, use filtered water and replace filter as recommended.

Ice Production & Selection

Adjust settings for ice size and production mode.

Ice Size: Press ICE SIZE to cycle through Small (fast production), Medium (standard), Large (slowest).
Energy Saver: Press and hold POWER for 3 seconds to enable/disable (reduces frequency of cycles).
Manual Override: Lift shut-off arm to stop production; lower to resume.
Ice Quality: Clear ice indicates good water quality; cloudy ice may suggest need for filter change.

Note: Changing ice size may temporarily halt production as system adjusts.

Cleaning & Maintenance

Regular cleaning ensures hygiene and performance.

Monthly: Wipe exterior with damp cloth; clean bin with mild detergent.
Quarterly: Run cleaning cycle (press CLEAN button for 5 seconds; cycle lasts 30 minutes).
Annually: Descale internal components with approved cleaner (follow instructions).
Air Filter: Remove and rinse under water every 6 months; let dry completely.

CAUTION! Unplug unit before cleaning interior. Do not use abrasive cleaners.

Water Filter Replacement

Replace filter every 6 months or when indicator light turns red.

Turn off ice maker and shut off water supply.
Locate filter housing (usually at rear or bottom).
Twist old filter counterclockwise to remove; discard.
Insert new filter (model: XYZ) and twist clockwise until snug.
Turn water back on; check for leaks.
Press and hold FILTER RESET button for 3 seconds to reset indicator.

WARNING! Use only Whirlpool-approved filters to prevent damage.

Energy Saving Tips

Enable Energy Saver mode during periods of low use.
Ensure unit is placed away from heat sources (ovens, direct sunlight).
Keep door seals clean and intact to maintain temperature.
Regularly clean condenser coils (if accessible) for efficient operation.

Safety Information

Read all instructions before use. Keep children away from moving parts. Do not operate if cord or plug is damaged. Disconnect power before servicing. Use only potable water supply. Ensure proper grounding of electrical outlet.

DANGER! Risk of electric shock. Do not immerse unit in water. Contact qualified technician for repairs.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No ice production	Power/water supply	Check if unit is plugged in and powered on; ensure water valve is open.
Ice cubes are small or misshapen	Water pressure/filter	Verify water pressure (20-120 psi); replace water filter.
Ice tastes or smells bad	Old filter/contamination	Replace water filter; clean storage bin and air filter.
Unit is noisy	Fan or motor issue	Ensure unit is level; check for obstructions in fan; contact service if noise persists.
Water leaking	Loose connections/clog	Tighten water line fittings; check drain hose for kinks or clogs.
Indicator light flashing	Error code	Refer to manual for specific flash patterns; reset by unplugging for 2 minutes.

Reset: Unplug for 5 minutes to reset control board.

Service: 1-800-253-1301; www.whirlpool.com